← Back to instrument record

STR26001 · Rev 2.0 · October 10, 2026

Tomatillo S-Type wiring reference

The five-way selector keeps the familiar S-type choices. The small switch changes the bridge-and-middle and middle-and-neck combinations from parallel to series; the single-pickup positions are unchanged.

Series switching · full circuit and operating statesOpen full sizeDownload PNG
STR26001 Tomatillo S-Type wiring reference showing Fender Custom Shop Tomatillo pickups, four-pole five-way super-switch contacts, a DPDT series switch, rear-view volume and tone controls, ten operating states, and common ground.

What each switch position does

Five-way positionNormalSeries
1BridgeBridge
2Bridge and middle in parallelMiddle and bridge in series
3MiddleMiddle
4Middle and neck in parallelMiddle and neck in series
5NeckNeck

Parts

Manufacturer pickup specifications: Fender Tomatillo pickup specifications.

  • Fender Custom Shop Tomatillo Stratocaster bridge, reverse-wound middle, and neck single-coil pickups with cloth-covered leads.
  • Four-pole five-way super switch and latching DPDT on-on micro switch.
  • A250K audio-taper master volume, A500K audio-taper master tone, 22 nF (0.022 µF) non-polarized tone capacitor, and mono output jack.
  • Treble bleed: a 1,200 pF capacitor in parallel with a 150 kΩ resistor, from the volume input, then a 20 kΩ resistor to the volume wiper.

Functional switch contacts

Contacts are shown by function. In each blade position, each pole common closes to one numbered throw.

Pole and common12345
A / BUSB_HM_HM_HM_HN_H
B / ORopenB_HopenN_Hopen
C / JopenB_HopenN_Hopen
D / M_CopenMRGNDMRopen

The DPDT has two independent poles. In normal mode, pole X joins OR to BUS and pole Y joins MR to GND. In series mode, X leaves OR open and Y joins MR to J, so the middle coil return feeds the selected outer pickup. OR and J are never joined. M_C has no permanent ground connection; any separate shield on the actual pickup goes independently to GND.

Connection map

NetConnect these points
B_HBridge hot to super-switch A1, B2, and C2.
M_HMiddle hot to super-switch A2, A3, and A4.
N_HNeck hot to super-switch A5, B4, and C4.
BUSSuper-switch A common, DPDT X normal throw, volume input, master-tone feed, and treble-bleed input.
OR / JSeparate B and C pole commons. OR goes to DPDT X common; J goes to DPDT Y series throw.
M_C / MRMiddle coil return M_C goes to pole D common. D2 and D4 join MR at DPDT Y common; D3 goes directly to GND.
TB_JThe 1,200 pF capacitor and 150 kΩ resistor run in parallel from BUS to TB_J. The 20 kΩ resistor runs from TB_J to OUT.
TC_JThe A500K tone wiper runs through the 22 nF capacitor to GND. The tone pot CCW lug takes BUS; its CW lug is unused.
OUTVolume wiper, treble-bleed output, and output-jack tip.
GNDBridge and neck coil returns; DPDT Y normal throw; volume track ground; tone-cap return; pot and switch cases, cavity shield, Fender tremolo/string ground, and jack sleeve.

In the diagram’s rear pot view, the shaft points away and the lugs point down. Left, center, and right are clockwise end, wiper, and counterclockwise end.

Build order

  1. Identify each pickup coil lead and map every contact of the actual super switch and DPDT by continuity.
  2. Connect coil hots to the selector, keep M_C isolated from fixed ground, and wire the two DPDT poles as separate routes.
  3. Wire BUS to master volume and tone, add the treble-bleed network and output jack, then bond all listed ground points.

Bench checks

  1. Identify the actual coil hot and return leads with a meter. The middle coil return M_C must have no fixed connection to ground; ground a separate shield independently if present.
  2. Map the actual super-switch and DPDT contacts by continuity before connecting the pickups. Keep OR and J separate.
  3. Tap-test the pickups in all ten selector and mode states against the table above. Check electrical phase and hum in both paired positions.
  4. Confirm clockwise volume and tone behavior, output-jack polarity, and continuity from the Fender tremolo and strings to jack sleeve.