K7RHY Resonance Lab
Crafted amplifier record
care card
5E3 Tweed-Style Tube Combo
An approximately 12-watt 5E3-style tube combo with interactive Normal and Bright channels and an Electro-Harmonix 12-inch speaker.
Inputs
- Normal 1
- Higher-sensitivity Normal input.
- Normal 2
- Lower-sensitivity Normal input.
- Bright 1
- Higher-sensitivity input with additional high-frequency presence.
- Bright 2
- Lower-sensitivity Bright input with a gentler response.
Controls
- Normal Volume
- Sets the Normal channel level; interacts with Bright Volume.
- Bright Volume
- Sets the Bright channel level; interacts with Normal Volume.
- Tone
- Shared tone control for both channels.
- Standby
- Use the supplied Quick Start and Controls guide for the switching sequence.
- Power
- Switches the amplifier on or off. Connect the speaker before switching on.
Speaker and essentials
- Output
- Approximately 12 watts.
- Speaker
- Electro-Harmonix, 12-inch, 75 watts, 8 ohms.
- Speaker connection
- Cable soldered at the speaker and plugged into the speaker-output jack.
- Fuse and mains lead
- 120 VAC, 60 Hz; 2A fuse; attached power cord.
Before switching on
- Unpack
- Remove all packing from the rear cabinet cavity.
- Speaker
- Check the existing plug is fully seated. Never operate with the speaker disconnected.
- Grounding
- Use a properly grounded outlet; never defeat the grounding pin.
- Service
- High voltage and stored charge are present inside. Do not open the chassis; use a qualified tube-amplifier technician.
The amplifier
This individually built combo is based on the late-1950s Fender 5E3 circuit. Its two channels have separate volume controls and a shared Tone control. The Normal and Bright Volume controls interact even when only one channel is in use: the unused channel's setting can change gain, tone, and response.
The installed Electro-Harmonix speaker is rated at 75 watts and 8 ohms. The speaker rating is distinct from the amplifier's approximately 12 watts of output. Its cable is soldered at the speaker and plugs into the amplifier's speaker-output jack; check that plug before operation.
Operating and service documentation
The amplifier was supplied with a completed Build Verification Record, as-shipped operating-voltage measurements, grounding and electrical-isolation test results, a Quick Start and Controls guide, and a High-voltage Safety Guide. Keep these amplifier-specific documents with the unit for future servicing.
View the original Build Verification Record, page 1.
These are builder-performed inspection and measurement records, not independent safety certification. Follow the supplied operating guide for the Power and Standby sequence.
Installed devices and electrical rating
The Build Verification Record (K7RHY-BVR-5E3-R1), dated August 15, 2026, records the following installed devices:
| Position | Device | Recorded maker |
|---|---|---|
| V1 — input/preamp | 12AX7 / ECC83S | JJ |
| V2 — gain/phase inverter | 12AX7 / ECC83S | JJ |
| V3 / V4 — output pair | 6V6GT pair | — |
| V5 — rectifier | 5Y3GT | — |
The rated mains supply is 120 VAC, 60 Hz, with a 2A fuse recorded as installed. The power and output transformers are identified as generic on the sheet, without maker or model details.
Recorded grounding and isolation checks
These are the builder's recorded results from August 15, 2026, not measurements taken for this web page. The sheet marks each check as passed. Test mains voltage was 116 VAC, and meter lead resistance was recorded as 0.05 ohms. Resistance values below are preserved as written on the sheet.
| Check | Recorded result |
|---|---|
| Mains-plug protective earth to exposed chassis | 0.3 ohms |
| Power-supply grounds to designated chassis/signal-ground reference | 0.1 ohms |
| Input-jack ground return | 0.1 ohms |
| Speaker-jack ground return | 0.3 ohms |
| Mains blades to chassis | L open / N open |
| Mains blades to speaker-output tip | L open / N open |
| Powered chassis relative to protective earth | 0.003 VAC / 0 VDC |
| Line conductor fused and switched; neutral not fused alone | Verified |
| Protective-earth termination, strain relief, mains clearances, and enclosure | Verified |
Safe use
Remove every piece of packing material from the rear cabinet cavity before connecting power. Operate only from a properly grounded outlet, with the speaker connected. Tubes become extremely hot during use.
Potentially lethal voltages and stored electrical charge are present inside the chassis. Do not open it or attempt internal service unless trained to work safely on high-voltage tube amplifiers.